Introduction
It’s a great feeling to own your own swimming pool. You can go for a swim, relax in the sun, or have friends over for drinks and snacks. But if you’re like most people, there are some things about maintaining your pool that may have slipped through the cracks. Luckily we’ve got this covered here! We’ll show you exactly what needs to be done and how best to do it so that your pool stays healthy forever (or at least until someone else buys it).
Get your equipment ready.
- Check that all the parts are there. You’ll need a good bit of time to do this properly, so make sure you have plenty of supplies and back-up equipment handy.
- Make sure everything works correctly before starting work on your pool. A malfunctioning pump could lead to a leaky liner or cracked walls, which could result in more expensive repairs than simply having the pool professionally cleaned and sanitized!
- Check that all parts are in good condition (including hoses). If they’re not, replace them immediately!
Test pool chemicals.
- Test the pH, alkalinity, and calcium hardness.
- pH is the measure of how acidic or basic your pool water is. A higher number means more acidic—a lower number means more basic. For example, if your meter reads 7.2 then you have a slightly acidic pool (7.0-7.8), while a reading between 7 and 8 would be considered neutral (7). The higher the reading goes up to 9 or 10 then this means that there’s way too much acid present in your swimming pool; this can cause corrosion on metal parts like stairs and pipes which could lead to leaks causing damage to your home!
Check the pH & alkalinity.
- Check the pH and alkalinity levels.
- The pool water should be between 7.2 and 7.6 in pH, with a recommended range of 8.2-8.8 (measured with a test kit). If your pool has low pH, you can add muriatic acid to bring it up; if it’s too high, add sodium bisulfate to decrease its concentration level; make sure that both products are added according to instructions on their packaging (you may need more than one type).
Check the calcium hardness.
Calcium hardness is a measurement of how much calcium is in your pool water. You can test it using a kit, but if you don’t have one, there are some other ways to determine if you need more calcium:
- If your water has a yellowish tinge to it, that means there’s too much chlorine in your system (and needs to be adjusted). Chlorine causes algae growth by acting as an anti-parasite agent—but it also kills off good bacteria needed for filtering out contaminants like dirt and dead scales on leaves or rocks in pools. So if these things start turning white or greenish-yellow after adding chlorine tablets or adding saltwater from the tap; chances are pretty high that something needs adjusting before adding any more chemicals into this equation!
Backwash the system.
The backwash process is a critical part of maintaining your pool filter. It’s important to backwash your system at least once every week because it cleans out any debris that may have accumulated in the filter. If you don’t perform this step, you run the risk of clogging your pump or skimmer basket and making any repairs more difficult.
Backwashing can be done manually or automatically depending on what type of equipment you have installed in your pool area. If you’re using an automatic backwash system (such as an automatic cleaner), make sure to schedule regular maintenance so that any manual cleaning is done between scheduled intervals.
Clean the filter and pump.
First, you’ll want to clean the filter and pump. You can use a pool vacuum to remove any leaves from around the skimmer basket or pump basket. Make sure that nothing is clogging inside these parts of your system; if there are some small bits of debris in them, clean them out with a brush attachment on an air hose or by hand.
Next, check all hoses and connections for leaks (not just at one end) by poking them with something like a stick or toothpick while they’re running water through them—you should hear any leaks when they’re turned on! If there are any cracks in hoses or connections then replace them immediately before it causes further damage which could lead into other problems later down line like leaking pipes under ground level causing flooding issues within homes above ground level as well as inside homes where residents live.
Shock the pool.
You should shock your pool at least once a week. The process helps to keep the water clean and sparkling, but it’s important to note that shocking should not be done immediately after you have cleaned your pool. If you do this, the chlorine will react with the water and cause a chemical reaction that can damage your pool equipment or leave minerals behind in the filter system (which could lead to algae growth). Therefore, it is recommended that you wait 24 hours before shocking a new system so as not to damage anything unnecessarily.
After shocking, let water sit overnight so that all of those chemicals have had time to dissipate naturally into the ground around where they were used. Then drain out any remaining unused chemicals from your system using either sand filters or pumps designed specifically for this purpose (such as Hayward’s Model 8000-A). Follow these steps carefully because if any part of these steps gets missed out then there could be serious consequences!
Brush and vacuum the pool.
Vacuum your pool.
This is one of the most important things you can do to keep your pool clean and healthy. Cleaning out debris and dirt from your pool is an essential part of maintaining a healthy environment for your family, friends, or neighbors to enjoy in the summertime. When it comes time to vacuum, use a brush designed specifically for cleaning pools (they come in different shapes and sizes). You’ll need to move around slowly so as not to damage any grout lines or tile edges with aggressive brushes; go over each section thoroughly before moving on. You should also vacuum any sand that collects at the bottom of your spa after every use so that bacteria doesn’t build up there—this will help prevent algae growth as well!
To make sure this step gets done regularly:
- If possible set up a schedule where someone else cleans once per week instead; if not then make sure everyone knows how often they should do it themselves based on their own personal schedules/preferences etc., but make sure everyone knows what needs doing before anyone starts working outside again!
Knowing how to maintain your pool will help you to enjoy it for years to come.
The first step in pool maintenance companies long island is to be aware of the risks. There are many things that can go wrong and you need to know how to fix them before they become a problem. If you’re not sure how it works, don’t risk damaging something important with an improper repair!
The next step is preparing yourself for the task at hand by reading up on proper maintenance practices and making sure you have all the tools necessary for any job (including swimming suits). Once this has been done, pick out some materials that will go into fixing whatever issue arises from neglecting proper care over time–if possible find someone who knows what they’re doing so that he/she can teach you when needed!
Conclusion
That’s it! You’re now ready to start enjoying your pool for years to come. Remember that even small pools can be expensive to maintain, so if you want yours to last longer, take care of it properly.